Trailer Wiring Harness Installation - 2010 Dodge Nitro- Video

Today on our 2010 Dodge Nitro, well be installing the Curt T-Connector 4-Pole Wiring Harness, part #C56183. To begin our install, well first open up the rear hatch and then well remove the two push pin fasteners that secure the rear taillight assembly. To remove the fasteners, we use a flat blade screwdriver prying out on the center and then completely removing the fastener. With both fasteners removed, well set them aside and then remove the taillight assembly, being careful not to break the alignment tabs underneath. After we pull the taillight assembly out, we can press on the locking tab for the connector and remove it from the assembly, setting the taillight assembly aside. Well go ahead and move over to the passenger side and repeat the same process. more

Watch Video

10/23/2013 9:37:57 AM

Trailer Wiring Harness Installation - 2010 Dodge Nitro 118554- Video

Today on our 2010 Dodge Nitro, well be installing the Tow Ready T-One vehicle wiring harness, part number 118554.Now to begin with, well need to raise the rear hatch of the vehicle. Well need to remove the light assembly from both the passenger and the drivers side. Well begin here on the drivers side. A flat head screwdriver or a trim panel removal tool works great for getting these two push pins that hold the light assembly in place. Once we have each of the push pin fasteners removed, well go ahead and work the light assembly out of the body of the vehicle.There are two additional tabs that just snap into place on the outer part of the light assembly. Once you have the light assembly worked out of the body, well go ahead and unplug the factory wiring harness from the back of it. more

Watch Video

10/21/2013 6:47:11 AM

Trailer Wiring Harness Installation - 2011 Dodge Nitro- Video

Today in our 2011 Dodge Nitro we'll be installing tow ready T1 connector part number 118554. Our first step of our install will be opening up the rear cargo door or removing the tail light housing on the driver side. To remove the housing or simply use a flat blade screwdriver and full off on the push-pin tabs to secured in the position. Popped it in out of place and setting it aside. Then we'll pop the rear tail light assembly out of place, being careful not to break the alignment tabs underneath. Then go and press on the locking connector for the manufacturers wire in to the back of the tail light assembly and disconnect the tail light assembly and set it aside. more

Watch Video

3/22/2013 9:11:20 AM

Trailer Wiring Harness Installation - 2008 Dodge Nitro- Video

Today on our 2008 Dodge Nitro well be installing the Curt T-connector four pull wiring harness, part number 55027. First well go ahead and open up the rear cargo door. Well need to remove the two fasteners securing each tail light assembly. To remove the fasteners well simply take a screwdriver and pop loose the pushpin fastener. Well go ahead and remove the fasteners and sit them aside then we can pop free the rear tail light assembly. Be careful as you pop it free not to break the alignment tabs on the inside. more

Watch Video

10/9/2012 2:18:35 PM

Trailer Wiring Harness Installation - 2008 Dodge Nitro 118554- Video

Today on this 2008 Dodge Nitro, were going to install part number 118554 from Tow Ready. First thing we need to do is go ahead and open up the back hatch and we need to remove the two tail lights. Well go ahead and remove these fasteners right here. We can restart it. Pop it straight back. Well unclip our wiring. more

Watch Video

4/5/2012 4:05:31 PM

Trailer Wiring Harness Installation - 2007 Dodge Nitro- Video

Today we will be working on a 2007 Dodge Nitro. We are going to install Tow Ready T-One wiring harness, part number 118421. First, we are going to access the rear cargo area of the vehicle. I am going to take a screw driver and pop out the two tabs here on the tail light lens. You will notice this application is already missing one. We will go ahead and take out the top one. This is the driver side of the vehicle. We will repeat the same process on the passenger side. :27 more

Watch Video

7/21/2011 1:04:31 PM

Wiring Harness Installation- 2010 Dodge Nitro- Video

Today on this 2010 Dodge Nitro we are going to install part number 118455 from Tow Ready. This is our T-One wiring harness. This T-One wiring harness does mount behind the tail lights on both sides of the vehicle. Also, there is a lead that will be run up to the battery for our 12 volt power supply. We will open the hatch and remove the tail lights. The lights are held on by the plastic rivets here and here. We are going to use a screw driver and pry the rivets out a little bit. Then we will use a trim tool and pull out the rivet. Pull straight back on it to release it. Then disconnect the light from the harness by pushing down on this tab right here. Go ahead and repeat for the other side. :45 more

Watch Video

3/30/2011 1:19:58 PM

  1